2 undrilled rods
Plain blanks for your own handle and carry setup.
1/2 × 5 inches
12.7 mm diameter × 127 mm length.
18,000 strikes
Per rod. Actual wear varies with technique and pressure.
See a ferro rod in action
Watch a shared FERROFIRE rod-and-striker demonstration.
The model, rod size and accessories shown may differ. This product is a bare-rod pack; the striker and other accessories shown are not included.
Choose the handle. Plan the exposed rod.
The FERROFIRE Heavy-Duty Plus No-Hole 2-Pack provides two bare ferrocerium rods for custom handles, camping kits and bushcraft practice. Each blank is 5 inches long and 1/2 inch in diameter.
These rods have no lanyard hole. Choose this version when your project uses a separate handle or storage arrangement rather than a cord threaded through the rod. When planning a handle, allow for the part of the rod it will cover and leave enough exposed length for your grip and striking technique.
Package contents: Two undrilled ferrocerium rods. No striker, handle or lanyard is included. Accessories shown in instructional images are not included.
At a glance
- Quantity: 2 rods
- Material: Ferrocerium
- Diameter: 1/2 inch (12.7 mm)
- Length: 5 inches (127 mm)
- Lanyard hole: None
- Strike capacity: 18,000 strikes per rod
- Striker: Not included
Prepare your rod and tinder
Five clear steps, plus a separate striker guide, each with its own photo. These shared technique photos show a different FERROFIRE setup. The striker, cord and assembled fire starter shown are not included in this pack of bare rods.
If you fit a custom handle, check that the rod is secure before striking. Begin with dry tinder and a separate ferro-rod striker, then practice directing sparks close to the tinder.
Step 1
Prepare your tinder
Gather dry, finely prepared tinder and kindling. Place the tinder on a suitable fire-safe surface.
Step 2
Expose the ferrocerium
Scrape a small area of the black protective coating away to reveal the silver ferrocerium underneath.
Step 3
Position the striker
Place the scraping edge against the exposed rod, close to your prepared tinder. Keep fingers and any cord clear of the striking path.
Step 4
Brace your hand
Hold the striker securely and keep that hand steady near the tinder. Check your grip before making a stroke.
Step 5
Pull the rod back
Draw the rod toward you against the steady striker to direct sparks into the tinder. Adjust the angle and pressure with practice.
Striker guide
Choose a scraping edge
Use a suitable ferro-rod striker. On the SA02 shown here, use a straight scraping edge for the rod; the serrated end helps prepare wood shavings.
Practice safely. Tinder preparation and technique matter. Sparks alone do not guarantee ignition, especially with damp tinder. Use only where fires are permitted, keep clear of other flammable items and fully extinguish your fire before leaving.
Before you choose
Does this version have a cord attachment hole?
No. This is the undrilled Heavy-Duty Plus rod. A cord cannot be threaded directly through it as supplied.
Are the rods supplied with handles?
No. Each is a bare 5-inch rod. Supply your own handle if your project requires one, and account for how much of the rod it will cover.
Does the five-inch length change the stated strike rating?
The stated rating for this 1/2-inch rod is 18,000 strikes per rod. The longer format does not change the rating used for this listing. Actual wear depends on your striker, pressure and technique.
How should I store the rods after practice?
Wipe them dry and store them away from moisture. Remove the black coating only where you intend to strike.
A closer look at the striking technique
Prepare suitable dry tinder and practice controlled strokes before relying on a ferro rod outdoors.
Shared FERROFIRE demonstration, not a presentation of this pack’s contents. The rod and accessories shown may differ. Use only where fires are permitted and fully extinguish any fire before leaving.












Thomas –
I was testing it out and it creates massive sparks to start a fire, theses will always be my last resorts and I’ll use other ones I have
Mike Morgan –
These Erro Rods work great !! They throw a good shower of sparks, using a Mora Bushcraft Black. No problem at all. Well pleased !!!
James –
I wanted something larger than what I have available around here, and this does the trick. Awesome!
big 10 inch –
I use a very coarse steel file to strike these on. They spark like a cutting torch throwing massive long burning sparks. Easily lights fires. I use it to light up magnesium
MT –
Thank you very much for your comments and trust in our brand.FERROFIRE will continue to work hard to bring better product experience to our customers.
WT –
Works very well. First scrape coating off to get a good spark.
Stacey R. –
Nice rods will last for a long time great sparks being thrown!
admin –
Thank you for the review! New item Heavy-duty plus ferro rod fire starter FS125 will be on sale on amazon.com on Aug 8th, it is including the heavy duty plus ferro rod you ordered. The earliest 5 review with 5 stars will be rewarded by full refund.
admin –
Thank you for the review! Sharing your order with friends on Facebook may get a coupon of 10% off, Come On !!